Step by Step Process to Install A Residential Sewer Line By Orange County Plumbing

Step by Step Process to Install A Residential Sewer Line By Orange County Plumbing

Steps to Install a Residential Sewer Line

To install the sewer line of your home, you need the assistance of Orange County Plumbing. Otherwise, it will not be done correctly. Your sewer pipe will connect your home with the private or municipal branch sewer line. Mainly, it is done under the street for a general installation. The pipe is buried under the front line.

The diameter of the pipe is 4 inches. The trench will be buried in is ready for it, sloped in position. The slope is the top priority here, and it is a significant part of the work. It is up to the slope to drain the water from the pipe with the help of gravity.

Steps to Install a Residential Sewer Line

The installation process of a sewer line may be done in five main steps. The authority of the local code controls the installation process. As we know, the approval comes from the administration after inspecting your side. It may be one or more than one times.

Fix the Depth

Determining the depths of the pipe is the first work of the installation process. The distance and depth of the pipe both are essential in this case. For the installation process of a residence, the beginning of the sewer pipes is in the exit of the main drain, near your house’s foundation.

The sewer line goes downward to be connected with the main or city branch to a connection named a tap. The elevations or depth of the pipes may be shown and measured with a GPS, laser level, and other regular equipment to survey.

 

Calculation of the Slope

With the help of the depth and length of the pipe, the preliminary calculations of the slope are done. The total elevation drop is gained by deducting the first elevation from the last elevation. This drop is divided by the entire length of the pipe, and the final slope is gained. You may calculate your own too. Suppose the connection of the pipe starts from an 8 feet dept, and the beginning of the pipe from your house is 6 feet. The calculated run is 80 feet.

Now the slope will be:

2/80= 0.025.

If you calculate the number in percentage, it will be 2.5 percent. The minimum average slope for laterals or most areas is 2 percent. In other words, the drop will be 2 feet in every 100 feet of run. The accurate slope may be higher than the target. But of course, it should be compatible with the local code. A slope in a higher position will make the liquids go faster than the solids, which leads to clogs. A too-small slope does not help adequately create enough force for the drainage system.

Digging the Trench

When you are digging the soil for a sewer line, you have to be careful of the lateral so that it does not cause any problems in the soil. The disturbance in the soil will make it condensed to lessen the settlement. The narrower the trench will be, the soil will be less disturbed. But only experts have clear ideas about the place of termination of the pipe.

A wide trench will be necessary too occasionally. The smooth and condensed bottom of the trench has to be according to the required slope. The materials used for bedding are mostly sand. It is laid in the trench. Its function is to provide constant support to the pipe. Sands can quickly slope compared to soil. It adjusts very nicely with the slope before you install the pipe.

 

Installation of the Pipe

Installing a sewer pipe is another critical process. A section of a sewer pipe is installed each time. Starting from the lower part of the run to the depth of the higher part. Nowadays, a modern pipe is produced from PVC. The pipes are joined with one another with the help of solvent adhesive and gasket fittings. The standard size of a sewer pipe for residential use is 4 inches. In addition, the local code is responsible for allowing the legal use of materials of the pipe and size.

The bell should always keep upwards to lessen the number of leaks at the joining point. The connection of the residence pipe with the main pipe is also under the city’s regulation. At the end of the house, most of the code needs precisely one or two cleanouts. It helps to give the pipe complete access so that you get a chance to clean it with the sewer auger at times necessary.

Rebury the Trench

When the lateral sewer installation is done and the final inspection gives a positive sign, it is time to rebury the trench and finish the project. The process starts by filling a sand layer. It protects the pipes and removes any gap surrounding the pipe. After that, another layer of soil is added to the trench.

The layers are cautiously dense so that it does not prevent settling in the future. The use of warning tape over the first layer of soil is an excellent idea. It alerts the crew about the pipe’s existence to avoid any sudden accident when someone else is digging in the area.

 

Last Words

The plumber in Orange County has an excellent idea about installing the residential sewer line. It is not a thing for DIY or a novice to handle. Slight mistakes can make you pay heavily. So, to install your sewer line, you should take assistance from a professional plumber.Visit our site now.